Five Peugeot Keys Lessons Learned From Professionals
Peugeot 208 Key Replacement
It is best to leave the replacement of Peugeot keys 208 to auto locksmiths who have the required equipment and know-how. They can make and program new keys faster than a dealership would and at a lower cost.
If your key fob has stopped locking or unlocking your doors, it could be due to a dead coin battery. There are many other reasons that the key could be malfunctioning.
Dead Coin Battery
A dead battery can stop your Peugeot 208 from locking and unlocking, and also stopping it from starting the engine. In this instance you'll need to make use of the alternative method for starting found in your vehicle's owner's manual.
Another reason why your 208 may not start is that the spark plugs are been worn down. The spark plugs are responsible for igniting the fuel that starts the engine. However they have a short lifespan. They'll eventually break down when they aren't used enough.
Fortunately, there's an easy solution to this problem. The best solution is to determine the voltage of your car battery using a multimeter. If the voltage falls below 11,5 volts then it's time to replace it. If the battery is corroded it is crucial to clean its contacts. This can be done by lifting the rubber covers that cover the two terminals on the battery and using wire brushes to clean any corroded areas of the battery. After that, you need to connect the positive pole cables to the negative.
Water Damage
If your 208 won't start and the battery has not been replaced, you must inspect the spark plugs. It could be that they're filthy, making them unable to spark. This is easily fixed by cleaning the spark plugs in the workshop.
Peugeot cars have keys that are transponder-type and is compatible with the car's immobiliser system. This guarantees that only the right key can turn the engine. If G28 inside the Peugeot key is damaged, it will not send the correct signal to the vehicle.
This is a typical issue that is caused by water damage. This is a common issue in more cold climates where the car has been exposed to rain or snow. If this is the case, contact a reputable auto locksmith who has all of the tools and equipment required to change the key's programming. They will also have all the latest technology and equipment required to make a Peugeot smart key. The process shouldn't take more than 15 minutes.
Contacts for the battery that are defective
Peugeot replaced the old transponder chips by introducing a new version that makes use of electronic components mounted on a circuitboard. The new system is fantastic when it's new, but the circuit boards deteriorate over time and cease to function properly.
This could prevent the immobiliser chip from activating the immobiliser chip, causing your car not to start. If this happens it's best to call a Peugeot specialist or locksmith.
A common issue occurs when the battery in the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a fresh blade for you, it's usually a simple fix.
Faulty Receiver Module
If your Peugeot key fob isn't working after dropping it on the floor, or being exposed to a sudden rain or accidentally washing it or washing it, it could be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer that regulates the central locking system of your Peugeot vehicle.
The key fob itself has rubber seals that block water from getting to the chip inside. However, prolonged exposure to water may penetrate these seals and damage the chip. Submerging the key fob into ocean water on the beach or throwing it into the pool can be especially damaging because of the high salt content.
The module will have to be replaced if the Peugeot spare key is no longer working. This is only performed by a professional auto locksmith or Peugeot specialist. Like other automobiles, Peugeot keys are protected by an exclusive immobilizer system that requires the right coding to begin the engine. This is why you should go with a knowledgeable Peugeot locksmith to handle the task of creating and programming the replacement.
Computer on-board is not working properly
The computer on the board of your Peugeot is the one responsible for all of the systems within your car, ranging from power windows to airbags. When something goes wrong with these systems, they will usually display a code indicating the problem. The code will be stored within the system until the issue is resolved. Most often, this involves the on-board computer being replaced.
One of the main reasons for the airbag light coming on is loose or corroded connections in the airbag sensor. This can be caused by wear and tear, age or exposure to salt and moisture. This issue must be addressed as soon you can, as an airbag that's malfunctioning could pose a risk in the event in the event of an accident.
If you notice an error message stating that the card is not found on your Peugeot key fob, the battery in the key fob might be weak or dead. This will stop the key fob sending a signal to deactivate your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then trying to start your car. If this does not work it is because the battery of the key must be replaced.